ZHAOYAO Multifunction Transistor Tester Automatic Identified Resistor Inductor Capacitor ESR Meter Checker Detector M328

Product parameters:Supported languages: Simplified Chinese, Traditional Chinese, English (three languages can be switched at will, please switch to the bottom of the product description)Appearance size: 70mm*135mm*24mmPower supply: DC9V (you need to bring your own 9V laminated battery 6F22)Weight: 0.128kg (without battery) Simple operation instructions: 1, 2, 3 pin free connection, automatic identification type, automatic detection of pin sequence, graphic display, automatic measurement parameters. Full fool operation, for example. You pick up a triode, you don't have to consider the BCE order of 123, just plug it. Then press the test button. He automatically identifies whether it is a triode, a FET, or a thyristor or a resistor or capacitor. . . . After being identified as a triode, the test is NPN or PNP, and then the BCE order is judged. Display it graphically, then tell you the magnification, turn-on voltage, and more. Basically you just need to plug in and press the button. He will tell you what is left. Test range description:Transistor range: 2 or less (including 2) PN junction transistors, do not have other internal resistance.Resistance measurement 0.5Ω-50MΩInductance measurement 0.01mH-20HCapacitance measurement 25pf - 100000uF Features:1: One-button measurement operation, the power is automatically turned off by the delay. The shutdown current is only 20nA and supports battery operation.2: Automatic detection of PNP and NPN bipolar transistors, N, P-channel MOSFETs, JFET FETs, diodes, dual diodes, thyristors, resistors, capacitors, inductors. The pin definition is automatically detected.3: Measure the current amplification factor (B) of the bipolar transistor and the conduction voltage (Uf) of the emitter junction. Darlington transistors can be identified by high threshold voltages and high current amplification factors.4: The protection diode inside the bipolar transistor and MOSFET can be detected and displayed on the screen.5: Measure the threshold voltage and gate capacitance of the MOSFET.6: Supports the measurement of two resistors, and the potentiometer can also measure. If the potentiometer is adjusted to one end of it, the tester cannot distinguish between the middle and the ends.7: The resolution of the resistance measurement is 0.1 ohm, and the highest measured value is 50M ohm.8: Capacitance measurement range from 25pf to 100mF (100,000UF). The resolution is up to 1 pF, and the inductance measurement range is 0.01 MH-20H. Otherwise, it will be displayed as a resistor. If the DC resistance of the inductor is higher than 2100 ohms, it will also be displayed as a resistor. In the capacitance test, the VLoss displayed on the screen is the meaning of loss and attenuation. The larger the value, the closer the capacitor is to scrapping! ESR is the impedance. The smaller the value, the better the capacitor performance!9: It can detect the equivalent series resistance (ESR) of capacitors above 2UF with a resolution of 0.01 ohms. This feature is very important for detecting capacitive performance.10: Two diodes can be displayed with the correct direction sign and the forward voltage drop is displayed.11: The LED is detected as a diode, and the forward voltage drop is higher than the normal value. The dual LEDs are detected as dual diodes. At the same time, the LED will flash.12: The time for each test is about two seconds. Only large capacitance and inductance measurements take a long time.GeneralBrandZHAOYAOModel320Quantity1 pieceMaterialABSSpecificationScreen Size-cmPowered By9V laminated battery 6F22Battery Number1Battery included or notNoPacking List1 x Transistor testerPackage Weight:0.131kg (0.289lb)Package Size:15cm x 8cm x 3cm (5.91in x 3.15in x 1.18in)